pressure washer won't start after running

Pull the trigger and pull start. Clean if dirty and replace if damaged.

Why Your Pressure Washer Won T Start And How To Fix It Youtube

Turn gas tap on gas tap valve controls fuel flow to carburetor.

. Once youve cleaned it try again. If your fuel is more than 30 days old dispose of it. The most likely scenario is bad fuel especially if your washer has been sitting unused for a while.

Even when using a hot water pressure washer you should never use water that has a temperature beyond 100 degrees Fahrenheit because this heat is bad for the entire system. Turn start switch to On. As your pressure washer runs gas is pumped out of the gas tank passed through the carburetor and burned in the engine to power the pump.

Turn choke on required for cold starts. The gas can simply be bad or it could have clogged the carburetor or worse. Some electric washers operate by battery.

So Make sure that you filled up your fuel tank of pressure washer properly and fully. Keep trying to pump water through the pressure washer until the air pressure has been removed from the hose. Ad Whirlpool not Spinning.

If the pressure washer doesnt start repeat these steps. Because electric washers are made to run with power most of the issues can be caused by electrical issues. When the engine warms up move the choke in to run position.

Check your air filter. Put the choke in the choke position as the engine is cold and it needs a little time to become warm. Always use fresh gas.

Now pull the pull string of the engine to start it up. Check the Fuel Cap. Some pressure washers may be rated for hot water and in this case if you were to supply the pressure washer with cold water you may have issues getting the desired pressure.

When this happens the engine wont have fuel going into the carburetor and therefore wont work properly. Turn garden hose On. There are a few reasons why your Troy-Bilt pressure washer wont start ranging from easy fixes to death declarations.

Remove water from the hose by allowing water to run through the pressure washer. You need to take out any form of hardened gas present. Use a spark plug tester to confirm that the spark plug is working properly.

Your pressure machines fuel tank could be empty and clear but you are trying to start for nothing without failure only. In this case your very first task will be to check the fuel tank if you are running a gas-powered pressure washer. If it doesnt work then you might need to do some deeper cleaning.

Remove the gas cap and fill the tank with gasoline. This will help the pump start and get water pressure flowing. This is a problem that is pretty easy to fix.

Next youll need to drain the gas tank and then. Change it if needed. Replace the gas cap and turn the pressure washer on.

If your machine is. Pull and hold lance trigger relieves pump pressure and also bleeds air from the pump. If the fuel cap is clogged the air cannot vent in.

A spark plug ignites the fuel in the engine so if it is defective the engine will not start. Obviously the first thing you want to check. If youre still having trouble starting your pressure washer after following these steps there may be water in the gas tank.

Run water through pressure washer until all air is removed from the hose. Pressure washers also called power washers are portable devices that dispense pressurized water through a nozzle removing dirt from the surface of objects. The only way to fix this is to clean the carburetor.

This air enters through the fuel cap. Removing air from the hose is a solution that many people try one that often works very well. Adjust the throttle lever situated on the right side of the engine to the fast setting.

You can also test the spark plug by removing it and holding it against the engine. As the gas leaves the air air needs to replace the void. Pressure washers are manufactured in two basic types.

Make sure your spark plug is connected to the wire. Clean the air filter if it is dirty. Get Help with your Appliance Online Save Time Now.

If your pressure washer doesnt start one issue could be a defective spark plug. Top off fuel in tank. If the fuel is left for more than 30 days dispose of it.

Examine the oil level and condition. However there can be other reasons why your washer isnt starting.

Why A Gas Powered Pressure Washer Won T Start The Family Handyman